78, Jalan Pasar, Pudu,
55100 Kuala Lumpur,
Malaysia.
+6012-716 1623
+603-9221 0207
+603-9221 8927
+603-9221 0207
+603-9221 8927
+603-9221 0819
- Audio Connectors
- AV Switcher/Converter/Splitter
- Arduino/MCU/Sensors
- Battery
- Battery Charger
- Cables
- DENN P.A. System
- Electronic Components
- Fan Spare Parts
- Inverter
- Measuring Devices/Multimeters
- Noise Monitoring LED
- Power Supply
- Power Stabiliser
- Refrigerator Spare Parts
- Remote Control
- RF Connectors
- Switches
- S H O W P.A. System
- Solar Power System
- AC Stepdown Transformer
- TOA P.A. System
- TV & Speaker Brackets
- Connector
- Pro's Kit Tools
- AC/DC Blower Fan
- Washing Machine Parts
- Others
Lian Hup Electronics And Electric Sdn Bhd
78, Jalan Pasar, Pudu,
55100 Kuala Lumpur,
Malaysia.
78, Jalan Pasar, Pudu,
55100 Kuala Lumpur,
Malaysia.
TP-5100 Lithium Battery Charging Management System Module/
| Previous | 16 / 47 | Next |
- Input Voltage Range: 5V to 15V DC (Absolute maximum up to 18V).
- Output Voltage: 4.2V (1S mode) or 8.4V (2S series mode).
- Maximum Charging Current: 2A (Adjustable via on-board sampling resistors).
- Charging Stages: 3-phase system (Trickle pre-charge ,Constant Current, Constant Voltage).
- Built-in Protections: Over-current, under-voltage, over-temperature, short-circuit, and battery reverse polarity protection.
Configuration & How to Use
1. Switching Between 1S (4.2V) and 2S (8.4V) Modes
The module features an on-board solder jumper labeled ''SET''.
- 1S Mode (4.2V default): Leave the SET pads open (un-soldered). Input voltage can be as low as 5V (e.g., standard USB).
- 2S Mode (8.4V): Short/solder the ''SET'' pads together. You must increase your input voltage to a minimum of 10V–12V (a 12V DC power adapter works perfectly).
2. Adjusting the Charging Current
Most standard modules come pre-configured for the maximum 2A output using two
0.1Ω resistors in parallel. If you are charging smaller batteries (like a standard 18650 cell that shouldn't exceed 1A), you can desolder or swap out the current-sensing resistors (Rs):- 0.1Ω resistor: Sets current to 1A.
- Two 0.1Ω resistors in parallel (0.05Ω): Sets current to 2A.
3. Wiring Connections
- IN+ / IN-: Connect your input power source (5V for 1S, or 12V for 2S).
- BAT+ / BAT-: Connect directly to the positive and negative terminals of your battery pack.
- LED Header: Features three pads to solder an external, dual-color LED if you are mounting the board inside an enclosure.
- Red LED On / Blue LED Off: Charging in progress.
- Blue (or Green) LED On / Red LED Off: Standby mode, fully charged, or no battery detected.
- No Internal Balancing: When using the TP5100 in 2S (8.4V) mode, it does not balance the two cells. It treats them as a single 8.4V block. If you are wiring two 18650 cells in series, you should ideally add a separate 2S BMS (Battery Management System) board between the charger and your batteries to ensure the cells stay balanced and safe.
- Heat Dissipation: While it runs cooler than linear modules, it can still get warm at a full 2A load. Ensure it has decent airflow if used continuously at maximum output.